Are your Scion xB door locks causing you fits? Get them fixed by following the tips in this guide. Shantui SL50W loader brake system troubleshooting methods for five common faults Brake System,Brake Pad Linning Pad,Hydraulic Valve Parts,Xcmg Loader Brake Caliper Jinan Union Construction Machinery Co., Ltd. , https://www.tfloaderparts.com
The loader has played a vital role in today's engineering construction. A good grasp of the characteristics of the loader's braking system and simple troubleshooting methods can ensure the normal use of the loader. Below, the editor will share with you the troubleshooting methods of five common faults of the loader brake system, I hope it will be helpful to everyone!
1. Run off after braking
The direct cause of deviation is caused by the unequal braking torque of the wheels on both sides. Common causes of failure:
(A) The Brake Caliper disc has serious oil pollution, and the friction system is seriously reduced, resulting in an imbalance of braking torque. At this time, the oil on the brake caliper disc should be removed;
(B) The sub-Cylinder piston is stuck and cannot work. Step on the brake of the stationary car, observe the working condition of the sub-cylinder, and dismantle and inspect as necessary.
2. The pressure of the barometer rises slowly
Main reason:
(A) Air leakage in the pipeline;
(B) The air pump is not working properly;
(C) The one-way valve is corroded and stuck;
(D) The drain bolt of the oil-water separator is not tightly closed or the pressure regulator valve is leaking.
Troubleshooting method: First, remove the air leakage in the pipeline, and then check the working status of the air pump. Remove the air pump outlet pipe and press the air outlet with your thumb. If the exhaust pressure is low, the air pump is malfunctioning. If the air pump is in good working condition, check the oil-water separator oil drain plug or pressure regulating valve to avoid bypass, and troubleshoot through inspection. Finally, check the two one-way valves in the three-way joint. The blockage of the one-way valve will cause the air reservoir to fail or slow down. In this way, the brake system failure of the loader can be solved.
3. Insufficient braking force, weak
Main reason:
(A) The brake leaks;
(B) There is air in the brake oil circuit;
(C) The wheel hub oil seal is broken, and there is grease on the clamp plate;
(D) The brake is severely worn and the friction surface is burned;
(E) Air pressure adjustment is too low.
The above-mentioned loader brake system failures can be eliminated by repairing, adjusting or replacing parts according to their respective causes.
4. When stepping on the brake, oil mist sprays out
(A) The brake light switch is damaged, and high pressure oil is sprayed from the switch interface. Replace the switch to solve it.
(B) The length of the piston rod of the afterburner pump is too large. This situation may occur when the afterburner pump assembly is newly replaced. The cause of the brake system failure of this loader is: the piston rod is adjusted too long, causing the piston stroke to be too large when the afterburner pump is working, and the brake fluid is drained The hole flows back into the afterburner pump and ejects.
During installation, the working stroke of the piston should be measured to determine the length of the piston rod.
5. Brake issuance
Fault phenomenon: The loader is struggling to walk and touch the clamp plate with hand after parking, the clamp plate becomes hot. main reason:
(A) The friction plate wears thin, the dust ring is damaged and water enters, and the piston is corroded and stuck;
(B) The return spring in the afterburner pump is weak or broken, and the high-pressure oil cannot be added.
SEM 50F, 650 Brake System
Liugong loaders ZL50CN, 855N, 856 Brake System,
SDLG 956L 952H 953 Brake System,
XCMG Brake System LW500KL ZL50GN,
Komatsu WA380, WA380-3, WA380-5, WA430-5 Brake System
DEGONG loader Brake System
Foton Lovol Loader Brake System
Lonking 855N loader Brake System
XGMA 932 936 956 Loader Brake System
Changlin Loader Brake System
Shantui SL50W Brake System
And we have more.
Are you struggling with your Scion xB’s door locks? Is one or all of them not working anymore? Don’t worry — this guide will walk you through the **most common issues and easy fixes** for power door lock problems on your Scion xB.
Genuine Scion xB parts here.
Power door locks are a convenience feature that we often take for granted — until they stop working. When they fail, it can be frustrating and even inconvenient. However, most power door lock problems are straightforward to diagnose and fix, especially if you know where to start.
Before diving into repairs, it's important to **identify the issue first**. Once you determine which part isn't working, you can follow the right steps to resolve it. Let's go over the most common scenarios.
### Remote Fails, Door Button Works
If your key fob no longer unlocks the car, but the button on the door still works, the problem is likely simple: your **key fob battery is dead**.
To fix it, open the key fob by gently squeezing its sides until it pops apart. Remove the old battery (usually a CR2032) and replace it with a new one. You can find these batteries at most electronics stores, supermarkets, or hardware stores. Once installed, your key fob should work again immediately.
### Single Door Fails To Lock/Unlock
If only one door is having trouble, the issue is probably a **faulty door actuator motor**. This small motor powers the locking mechanism and can wear out over time.
Here’s how to replace it:
1. Order a replacement actuator from a trusted supplier.
2. Remove the door panel by unscrewing all the screws — including those behind the speaker and in the door handle.
3. Carefully pull the panel away using a plastic trim tool or a flathead screwdriver. You may hear clips clicking as they release.
4. Disconnect the electrical connector for the power locks and windows.
5. Peel back the inner door cover to access the actuator.
6. Swap out the old motor with the new one.
7. Reassemble everything in reverse order.
This process usually takes about an hour, depending on your experience level.
### All Doors/Multiple Doors Fail To Lock/Unlock
If multiple doors or all doors aren’t responding, the issue could be either a **blown fuse** or a more complex **wiring problem**.
Check the fuse box for the door/window fuse. If it’s blown, replace it with a new one of the same rating. However, if the power windows still work, the fuse might not be the issue.
If replacing the fuse doesn’t help, and the key fob and individual door locks are working fine, then there may be a deeper electrical problem. In such cases, it’s best to consult a **certified mechanic** who can properly diagnose and repair the system.
---
**Still have questions?** Check out these related guides for more help:
- [Scion tC Power Door Lock Failure Guide](#)
- [Scion xD Power Door Lock Failure Guide](#)
- [Scion xB Power Window Failure Guide](#)
- [Toyota 4Runner Door Lock Failure – Diagnose Guide](#)
- [Toyota Yaris Door Lock Failure – Diagnose Guide](#)
- [Toyota Sequoia Door Lock Failure – Diagnose Guide](#)
If you're unsure about any step, don’t hesitate to reach out for professional assistance. Safety and proper function are always worth the extra effort.